Query: What is the recommended recalibration interval for the Tolvan A3? average_relevancy=0.5566 ndcg=1.0000 --- rank 1 by relevancy --- similarity=0.8050 relevancy=1.0000 source=06c5221a-8323-49d4-8bf0-02db17c0c558/4dece290-11ac-46c2-8d2e-99a00b6e2193/A10_tolvan_a3_product_overview.md # Tolvan A3 - product overview The Tolvan A3 is a conductivity and temperature sensor built for continuous deployment in estuarine and coastal water. It is the instrument most of our customers meet first, and most of the questions the service desk answers are about this one. ## What it measures The instrument reports conductivity, temperature and a derived practical salinity. Conductivity is measured with an inductive cell, which has no exposed electrodes to foul or to wear, and temperature with a thermistor mounted in the same flow path so that the two readings describe the same parcel of water. Pressure is not measured; where a depth record is needed, the instrument is paired with a separate pressure sensor on the same mooring. ## Where it is used Typical deployments are estuary monitoring for a regulator, intake monitoring for a water treatment works, and baseline surveys ahead of construction in a harbour. It is rated for continuous immersion to fifty metres. Deeper work uses the Tolvan C5, which shares the sensing arrangement in a pressure housing rated considerably deeper. ## How it is powered and read On a mooring, the instrument runs from an internal battery pack and logs to internal memory. On a cabled installation it is powered over the same cable that carries its data, and reports continuously to the Brannoc telemetry gateway, which forwards to the customer's own system. The two modes are configured at commissioning and are not switched in the field. ## Fouling and cleaning In estuarine water the practical limit on deployment is biological fouling rather than power or memory. An anti-fouling guard and a sacrificial anode are fitted at commissioning and replaced at each service visit. Customers in warm or nutrient-rich water are advised to shorten the interval between visits rather than to clean the sensing face themselves, because the inductive cell is easily damaged by an abrasive. ## Calibration Every instrument leaves the laboratory with a signed certificate recording the as-found and as-left bias at four reference points across the working range. The recommended recalibration interval for the Tolvan A3 is 22 months from the date of the last certificate. An instrument returned early because of a suspected drift is checked as found before anything is adjusted, so that the drift can be quantified rather than merely corrected. --- rank 2 by relevancy --- similarity=0.7579 relevancy=0.9842 source=06c5221a-8323-49d4-8bf0-02db17c0c558/4dece290-11ac-46c2-8d2e-99a00b6e2193/A03_calibration_certificate_scan.pdf INSTRUMENT **Tolvan A3 conductivity-temperature sensor** SERIAL NUMBER **FW-A3-40871** CUSTOMER **Severn Estuary Monitoring Partnership** ORDER REFERENCE **SEMP/PO/9134** DATE OF CALIBRATION **3 March 2026** NEXT CALIBRATION DUE **3 January 2028** PROCEDURE **FWL-CAL-114, issue 6** AMBIENT **20.4 C, 61 % RH** --- ## Results Salinity channel, checked against reference standard SR-2 at four points | Reference point | Reference value | As found | As left | | --------------- | --------------- | -------- | ------- | | Point 1 | 5.000 psu | 4.961 psu | 4.997 psu | | Point 2 | 15.000 psu | 14.964 psu | 14.996 psu | | Point 3 | 25.000 psu | 24.962 psu | 24.995 psu | | Point 4 | 35.000 psu | 34.965 psu | 34.997 psu | ## Summary As-found bias, mean of four points: -0.037 psu As-left bias, mean of four points: -0.004 psu Expanded uncertainty (k = 2): 0.008 psu The instrument was adjusted after the as-found check and passed. Conductivity cell and thermistor were cleaned before the as-found run. Signed, calibration engineer M. Ottaway --- rank 3 by relevancy --- similarity=0.7134 relevancy=0.4209 source=06c5221a-8323-49d4-8bf0-02db17c0c558/4dece290-11ac-46c2-8d2e-99a00b6e2193/A08_warranty_terms_sales_pack.pdf Sales pack Page 1 Fenwake Instruments Ltd Warranty Terms Sales pack - customer-facing warranty terms 1. What is covered These are the warranty terms that accompany a new instrument. They apply to every new Tolvan A3 supplied by Fenwake Instruments Ltd, however it was ordered and wherever it is deployed. The warranty covers the instrument, its pressure housing, its connector and any cable supplied with it. It covers failure arising from a defect in materials or workmanship. Where a covered failure occurs, Fenwake repairs or exchanges the instrument at its own option and bears the cost of carriage in both directions. 2. The warranty period Every new Tolvan A3 carries a warranty of 24 months from the date the instrument is delivered. The period runs from delivery rather than from commissioning, and is not extended by a repair carried out under it. 2.1 Instruments repaired under warranty A repaired instrument carries the unexpired balance of the original period, or ninety days from the return of the repaired instrument, whichever ends later. 3. What is not covered • Fouling, corrosion of sacrificial components, and wear of consumables such as anodes, guards and gland kits. • Damage caused by a mooring failure, a vessel strike, a snagged cable or any other mechanical event outside the instrument. • Damage caused by opening the housing outside a Fenwake workshop, or by breaking a calibration seal. • Drift within the published specification. Drift is a calibration matter, not a defect. • Any instrument whose serial number has been removed or altered. 4. Making a claim A claim is made through the service desk, quoting the serial number and the delivery note. The service desk raises a ticket, arranges return carriage and tells the customer within five working days whether the failure is covered. Where it is not covered, the customer is quoted for the repair before any work starts. 4.1 If the customer disagrees Where a customer disputes a decision that a failure is not covered, the instrument is held unrepaired and the head of service operations reviews the file. The instrument is not returned, scrapped or repaired while a review is open. Fenwake Instruments Ltd - Warranty Terms Sales pack Page 2 --- rank 4 by relevancy --- similarity=0.7125 relevancy=0.3781 source=06c5221a-8323-49d4-8bf0-02db17c0c558/4dece290-11ac-46c2-8d2e-99a00b6e2193/A09_warranty_statement_service_pack.pdf Service pack Page 1 Fenwake Instruments Ltd Warranty Terms Service pack - warranty terms for the service desk 1. What is covered These are the warranty terms the service desk applies when a customer reports a failure. They apply to every new Tolvan A3 supplied by Fenwake Instruments Ltd, however it was ordered and wherever it is deployed. The warranty covers the instrument, its pressure housing, its connector and any cable supplied with it. It covers failure arising from a defect in materials or workmanship. Where a covered failure occurs, Fenwake repairs or exchanges the instrument at its own option and bears the cost of carriage in both directions. 2. The warranty period Every new Tolvan A3 carries a warranty of 36 months from the date the instrument is delivered. The period runs from delivery rather than from commissioning, and is not extended by a repair carried out under it. 2.1 Instruments repaired under warranty A repaired instrument carries the unexpired balance of the original period, or ninety days from the return of the repaired instrument, whichever ends later. 3. What is not covered • Fouling, corrosion of sacrificial components, and wear of consumables such as anodes, guards and gland kits. • Damage caused by a mooring failure, a vessel strike, a snagged cable or any other mechanical event outside the instrument. • Damage caused by opening the housing outside a Fenwake workshop, or by breaking a calibration seal. • Drift within the published specification. Drift is a calibration matter, not a defect. • Any instrument whose serial number has been removed or altered. 4. Making a claim A claim is made through the service desk, quoting the serial number and the delivery note. The service desk raises a ticket, arranges return carriage and tells the customer within five working days whether the failure is covered. Where it is not covered, the customer is quoted for the repair before any work starts. 4.1 If the customer disagrees Where a customer disputes a decision that a failure is not covered, the instrument is held unrepaired and the head of service operations reviews the file. The instrument is not returned, scrapped or repaired while a Fenwake Instruments Ltd - Warranty Terms Service pack Page 2 review is open. --- rank 5 by relevancy --- similarity=0.6928 relevancy=0.0000 source=06c5221a-8323-49d4-8bf0-02db17c0c558/4dece290-11ac-46c2-8d2e-99a00b6e2193/A10_tolvan_a3_product_overview.md ## Firmware Firmware is updated during a service visit rather than over the telemetry link, because an interrupted update on a deployed instrument leaves it unreadable until it is recovered. A customer who declines a recommended update is asked to confirm in writing, and the confirmation is attached to the instrument record.