{
  "markdown": "Tarnbeck Institute of Hydrology TIH/TN/18\nPage 1 of 3\nA one-dimensional model of tidal attenuation in the Braithe channel\nTechnical note TIH/TN/18 \u00b7 January 2026\nR. K. Sandiman and H. Vale\n1 Introduction\nThe tide entering the Braithe is attenuated over the eleven kilometres between the bar and Braithe\nBridge, and the attenuation is large enough to matter to anyone predicting water levels in the upper\nestuary. This note sets out the one-dimensional model the Institute has used since 2018, states the\napproximation on which the working formula rests, and compares the result with the gauge record at\nthree stations.\nNothing here is new. The intention is to have the derivation, the assumptions and the coefficients in one\nplace, because the formula has been quoted in Partnership papers without them.\n2 Governing equations\nTake the channel as a single reach of slowly varying cross-section and neglect lateral inflow.\nConservation of mass gives\n(1)\nwhere A is the cross-sectional area below the free surface and Q the discharge through it. Conservation of\nmomentum, with friction represented in the Manning form, gives\n(2)\nin which is the surface elevation above mean sea level, n is Manning's coefficient, R the hydraulic\nradius for wetted perimeter P, and g the acceleration due to gravity. The friction term is the only\nnonlinear one that matters over the range of interest.\n3 Attenuation of the leading harmonic\nFor a channel of nearly uniform depth the leading semidiurnal harmonic decays close to exponentially\nwith distance upstream, so that\n(3)\nwith the amplitude at the bar, the angular frequency of the harmonic, k the wavenumber and the\nattenuation coefficient. Linearising the friction term by the Lorentz method and collecting terms gives\n\u2202A\n\u2202t + \u2202Q\n\u2202x = 0\n\u2202Q\n\u2202t + \u2202\n\u2202x(\nQ 2\nA ) + gA \u2202\u03b7\n\u2202x + g n2 Q |Q|\nA R 4/3 = 0\n\u03b7\nR = A/P\n\u03b7(x, t) = \u03b70 e\u2212\u03bcx cos (\u03c9t \u2212 kx)\n\u03b70\t\u03c9\t\u03bc\n\n-- 1 of 3 --\n\nTarnbeck Institute of Hydrology TIH/TN/18\nPage 2 of 3\n(4)\nwhere c is the frictionless wave speed and h the mean depth. The second expression is the friction\nparameter; it is small in the lower reach and approaches unity above Harrowby Reach, which is where\nthe exponential form begins to fail.\n4 Application to the Braithe\nTaking the mean depth as eleven metres below the bar and four metres at the bridge, with Manning's\ncoefficient at the value fitted in 2018, the formula reproduces the observed amplitude at Vardenne Quay\nto within four per cent and at Harrowby Reach to within nine. At Braithe Bridge it overestimates the\namplitude, and the discrepancy grows through the spring tides, which is the behaviour the friction\nparameter predicts.\nA two-reach treatment with separate depths would probably remove most of the error at the bridge. It has\nnot been attempted here because the gauge record above Harrowby Reach is too short to fit a second\ncoefficient with any confidence.\n5 Coefficients\nManning's coefficient is not constant with depth in a channel of this kind, and the single fitted value used\nabove is a compromise. Fitting the 2018 record with a depth-dependent form gives\n(5)\nwith the deep-water value and b a bed constant. The fit is better in the lower reach and no better at\nthe bridge, which suggests that the error there is not in the friction term at all.\nThe two constants were fitted to the 2018 record and have not been refitted since. Refitting on the four\nyears now available would be worth doing; the Institute's expectation is that the deep-water value will\nmove very little and the bed constant appreciably, because it is carrying the shallow reaches where the\nrecord has improved most.\n6 Limitations\nThree limitations should be stated plainly. The first is the one-dimensional assumption, which fails where\nthe channel divides above Harrowby Reach. The second is the neglect of the freshwater inflow, which is\nsmall in summer and not small after rain. The third is the linearisation itself, which is a poor\napproximation once the friction parameter approaches unity - that is, in exactly the reach where the\nmodel is least accurate.\nThe error measure quoted in the previous section is\n\u03bc = \u03c9\nc (\n\u03c7\n2(1 + \u03c72))\n1/2\n, \u03c7 = 8 n2 c \u03b70\n3\u03c0 h 4/3\nn(h) = n\u221e + b\nh 1/3\nn\u221e\n\n-- 2 of 3 --\n\nTarnbeck Institute of Hydrology TIH/TN/18\nPage 3 of 3\n(6)\ntaken over the spring-neap cycle at each gauge, with the observed amplitude and the modelled\none. It is a crude measure and it flatters the model at the bar, where the amplitude is large and the\nabsolute error is not.\nNone of this is an argument against using the formula, which is quick, transparent and good enough for\nthe purposes the Partnership puts it to. It is an argument for quoting it with the reach and the tidal range\nattached, which the papers that quote it have not always done.\nReferences\nSandiman, R. K. (2018). Tidal propagation in the Braithe: a first fit. Tarnbeck Institute internal report TIH/IR/09.\nVale, H. and Croyde, P. (2021). The Harrowby Reach gauge, 2015 to 2020. Journal of Estuarine Hydrology 44,\n218-31.\nProsser, A. (2009). Friction coefficients for the Braithe channel. Braithe Harbour Board, unpublished.\n\u03b5 = |\u03b7o \u2212 \u03b7m|\n\u03b7o\u03b7o\t\u03b7m\n\n-- 3 of 3 --\n\n",
  "pageCount": 3,
  "model": "nano",
  "credits": 3,
  "requestId": 272372
}